Header logo is

293 results (View BibTeX file of all listed publications)

2015

Thumb xl screen shot 2015 09 09 at 12.09.20
Untethered Magnetic Micromanipulation

Diller, E., Sitti, M.

In Micro-and Nanomanipulation Tools, 13, 10, Wiley-VCH Verlag GmbH & Co. KGaA, November 2015 (inbook)

Abstract
This chapter discusses the methods and state of the art in microscale manipulation in remote environments using untethered microrobotic devices. It focuses on manipulation at the size scale of tens to hundreds of microns, where small size leads to a dominance of microscale physical effects and challenges in fabrication and actuation. To motivate the challenges of operating at this size scale, the chapter includes coverage of the physical forces relevant to microrobot motion and manipulation below the millimeter-size scale. It then introduces the actuation methods commonly used in untethered manipulation schemes, with particular focus on magnetic actuation due to its wide use in the field. The chapter divides these manipulation techniques into two types: contact manipulation, which relies on direct pushing or grasping of objects for motion, and noncontact manipulation, which relies indirectly on induced fluid flow from the microrobot motion to move objects without any direct contact.

pi

DOI Project Page [BibTex]

2015

pi Diller, E., Sitti, M. Untethered Magnetic Micromanipulation In Micro-and Nanomanipulation Tools, 13, 10, Wiley-VCH Verlag GmbH & Co. KGaA, November 2015 (inbook)

DOI Project Page [BibTex]

Thumb xl 07353111
Compliant wing design for a flapping wing micro air vehicle

Colmenares, D., Kania, R., Zhang, W., Sitti, M.

In Intelligent Robots and Systems (IROS), 2015 IEEE/RSJ International Conference on, pages: 32-39, September 2015 (inproceedings)

Abstract
In this work, we examine several wing designs for a motor-driven, flapping-wing micro air vehicle capable of liftoff. The full system consists of two wings independently driven by geared pager motors that include a spring in parallel with the output shaft. The linear transmission allows for resonant operation, while control is achieved by direct drive of the wing angle. Wings used in previous work were chosen to be fully rigid for simplicity of modeling and fabrication. However, biological wings are highly flexible and other micro air vehicles have successfully utilized flexible wing structures for specialized tasks. The goal of our study is to determine if wing flexibility can be generally used to increase wing performance. Two approaches to lift improvement using flexible wings are explored, resonance of the wing cantilever structure and dynamic wing twisting. We design and test several wings that are compared using different figures of merit. A twisted design improved lift per power by 73.6% and maximum lift production by 53.2% compared to the original rigid design. Wing twist is then modeled in order to propose optimal wing twist profiles that can maximize either wing efficiency or lift production.

pi

DOI [BibTex]

pi Colmenares, D., Kania, R., Zhang, W., Sitti, M. Compliant wing design for a flapping wing micro air vehicle In Intelligent Robots and Systems (IROS), 2015 IEEE/RSJ International Conference on, pages: 32-39, September 2015 (inproceedings)

DOI [BibTex]

Thumb xl toc image patent
Methods of forming dry adhesive structures

Sitti, M., Murphy, M., Aksak, B.

September 2015, US Patent 9,120,953 (patent)

Abstract
Methods of forming dry adhesives including a method of making a dry adhesive including applying a liquid polymer to the second end of the stem, molding the liquid polymer on the stem in a mold, wherein the mold includes a recess having a cross-sectional area that is less than a cross-sectional area of the second end of the stem, curing the liquid polymer in the mold to form a tip at the second end of the stem, wherein the tip includes a second layer stem; corresponding to the recess in the mold, and removing the tip from the mold after the liquid polymer cures.

pi

[BibTex]

pi Sitti, M., Murphy, M., Aksak, B. Methods of forming dry adhesive structures September 2015, US Patent 9,120,953 (patent)

[BibTex]

no image
Millimeter-scale magnetic swimmers using elastomeric undulations

Zhang, J., Diller, E.

In 2015 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pages: 1706-1711, September 2015 (inproceedings)

Abstract
This paper presents a new soft-bodied millimeterscale swimmer actuated by rotating uniform magnetic fields. The proposed swimmer moves through internal undulatory deformations, resulting from a magnetization profile programmed into its body. To understand the motion of the swimmer, a mathematical model is developed to describe the general relationship between the deflection of a flexible strip and its magnetization profile. As a special case, the situation of the swimmer on the water surface is analyzed and predictions made by the model are experimentally verified. Experimental results show the controllability of the proposed swimmer under a computer vision-based closed-loop controller. The swimmers have nominal dimensions of 1.5×4.9×0.06 mm and a top speed of 50 mm/s (10 body lengths per second). Waypoint following and multiagent control are demonstrated for swimmers constrained at the air-water interface and underwater swimming is also shown, suggesting the promising potential of this type of swimmer in biomedical and microfluidic applications.

pi

link (url) DOI [BibTex]

pi Zhang, J., Diller, E. Millimeter-scale magnetic swimmers using elastomeric undulations In 2015 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pages: 1706-1711, September 2015 (inproceedings)

link (url) DOI [BibTex]

Thumb xl publications toc
Experimental investigation of optimal adhesion of mushroomlike elastomer microfibrillar adhesives

Marvi, H., Song, S., Sitti, M.

Langmuir, 31(37):10119-10124, American Chemical Society, August 2015 (article)

Abstract
Optimal fiber designs for the maximal pull-off force have been indispensable for increasing the attachment performance of recently introduced gecko-inspired reversible micro/nanofibrillar adhesives. There are several theoretical studies on such optimal designs; however, due to the lack of three-dimensional (3D) fabrication techniques that can fabricate such optimal designs in 3D, there have not been many experimental investigations on this challenge. In this study, we benefitted from recent advances in two-photon lithography techniques to fabricate mushroomlike polyurethane elastomer fibers with different aspect ratios of tip to stalk diameter (β) and tip wedge angles (θ) to investigate the effect of these two parameters on the pull-off force. We found similar trends to those predicted theoretically. We found that β has an impact on the slope of the force-displacement curve while both β and θ play a role in the stress distribution and crack propagation. We found that these effects are coupled and the optimal set of parameters also depends on the fiber material. This is the first experimental verification of such optimal designs proposed for mushroomlike microfibers. This experimental approach could be used to evaluate a wide range of complex microstructured adhesive designs suggested in the literature and optimize them.

pi

DOI [BibTex]

pi Marvi, H., Song, S., Sitti, M. Experimental investigation of optimal adhesion of mushroomlike elastomer microfibrillar adhesives Langmuir, 31(37):10119-10124, American Chemical Society, August 2015 (article)

DOI [BibTex]

Thumb xl toc image patent
Micro-fiber arrays with tip coating and transfer method for preparing same

Sitti, M., Washburn, N. R., Glass, P. S., Chung, H.

July 2015, US Patent 9,079,215 (patent)

Abstract
Present invention describes a patterned and coated micro- and nano-scale fibers elastomeric material for enhanced adhesion in wet or dry environments. A multi-step fabrication process including optical lithography, micromolding, polymer synthesis, dipping, stamping, and photopolymerization is described to produce uniform arrays of micron-scale fibers with mushroom-shaped tips coated with a thin layer of an intrinsically adhesive synthetic polymer, such as lightly crosslinked p(DMA-co-MEA).

pi

[BibTex]

pi Sitti, M., Washburn, N. R., Glass, P. S., Chung, H. Micro-fiber arrays with tip coating and transfer method for preparing same July 2015, US Patent 9,079,215 (patent)

[BibTex]

Thumb xl publications toc
pH-taxis of biohybrid microsystems

Zhuang, J., Carlsen, R. W., Sitti, M.

Scientific reports, 5, Nature Publishing Group, June 2015 (article)

Abstract
The last decade has seen an increasing number of studies developing bacteria and other cell-integrated biohybrid microsystems. However, the highly stochastic motion of these microsystems severely limits their potential use. Here, we present a method that exploits the pH sensing of flagellated bacteria to realize robust drift control of multi-bacteria propelled microrobots. Under three specifically configured pH gradients, we demonstrate that the microrobots exhibit both unidirectional and bidirectional pH-tactic behaviors, which are also observed in free-swimming bacteria. From trajectory analysis, we find that the swimming direction and speed biases are two major factors that contribute to their tactic drift motion. The motion analysis of microrobots also sheds light on the propulsion dynamics of the flagellated bacteria as bioactuators. It is expected that similar driving mechanisms are shared among pH-taxis, chemotaxis, and thermotaxis. By identifying the mechanism that drives the tactic behavior of bacteria-propelled microsystems, this study opens up an avenue towards improving the control of biohybrid microsystems. Furthermore, assuming that it is possible to tune the preferred pH of bioactuators by genetic engineering, these biohybrid microsystems could potentially be applied to sense the pH gradient induced by cancerous cells in stagnant fluids inside human body and realize targeted drug delivery.

pi

DOI Project Page [BibTex]

pi Zhuang, J., Carlsen, R. W., Sitti, M. pH-taxis of biohybrid microsystems Scientific reports, 5, Nature Publishing Group, June 2015 (article)

DOI Project Page [BibTex]

Thumb xl publications toc
Fiberbot: A miniature crawling robot using a directional fibrillar pad

Han, Y., Marvi, H., Sitti, M.

In Robotics and Automation (ICRA), 2015 IEEE International Conference on, pages: 3122-3127, May 2015 (inproceedings)

Abstract
Vibration-driven locomotion has been widely used for crawling robot studies. Such robots usually have a vibration motor as the actuator and a fibrillar structure for providing directional friction on the substrate. However, there has not been any studies about the effect of fiber structure on robot crawling performance. In this paper, we develop Fiberbot, a custom made mini vibration robot, for studying the effect of fiber angle on robot velocity, steering, and climbing performance. It is known that the friction force with and against fibers depends on the fiber angle. Thus, we first present a new fabrication method for making millimeter scale fibers at a wide range of angles. We then show that using 30° angle fibers that have the highest friction anisotropy (ratio of backward to forward friction force) among the other fibers we fabricated in this study, Fiberbot speed on glass increases to 13.8±0.4 cm/s (compared to ν = 0.6±0.1 cm/s using vertical fibers). We also demonstrate that the locomotion direction of Fiberbot depends on the tilting direction of fibers and we can steer the robot by rotating the fiber pad. Fiberbot could also climb on glass at inclinations of up to 10° when equipped with fibers of high friction anisotropy. We show that adding a rigid tail to the robot it can climb on glass at 25° inclines. Moreover, the robot is able to crawl on rough surfaces such as wood (ν = 10.0±0.2 cm/s using 30° fiber pad). Fiberbot, a low-cost vibration robot equipped with a custom-designed fiber pad with steering and climbing capabilities could be used for studies on collective behavior on a wide range of topographies as well as search and exploratory missions.

pi

DOI [BibTex]

pi Han, Y., Marvi, H., Sitti, M. Fiberbot: A miniature crawling robot using a directional fibrillar pad In Robotics and Automation (ICRA), 2015 IEEE International Conference on, pages: 3122-3127, May 2015 (inproceedings)

DOI [BibTex]

Thumb xl publications toc
Platform design and tethered flight of a motor-driven flapping-wing system

Hines, L., Colmenares, D., Sitti, M.

In Robotics and Automation (ICRA), 2015 IEEE International Conference on, pages: 5838-5845, May 2015 (inproceedings)

Abstract
In this work, we examine two design modifications to a tethered motor-driven flapping-wing system. Previously, we had demonstrated a simple mechanism utilizing a linear transmission for resonant operation and direct drive of the wing flapping angle for control. The initial two-wing system had a weight of 2.7 grams and a maximum lift-to-weight ratio of 1.4. While capable of vertical takeoff, in open-loop flight it demonstrated instability and pitch oscillations at the wing flapping frequency, leading to flight times of only a few wing strokes. Here the effect of vertical wing offset as well as an alternative multi-wing layout is investigated and experimentally tested with newly constructed prototypes. With only a change in vertical wing offset, stable open-loop flight of the two-wing flapping system is shown to be theoretically possible, but difficult to achieve with our current design and operating parameters. Both of the new two and four-wing systems, however, prove capable of flying to the end of the tether, with the four-wing system prototype eliminating disruptive wing beat oscillations.

pi

DOI [BibTex]

pi Hines, L., Colmenares, D., Sitti, M. Platform design and tethered flight of a motor-driven flapping-wing system In Robotics and Automation (ICRA), 2015 IEEE International Conference on, pages: 5838-5845, May 2015 (inproceedings)

DOI [BibTex]

Thumb xl 1 s2.0 s0141635915000938 main
Structural optimization for flexure-based parallel mechanisms–Towards achieving optimal dynamic and stiffness properties

Lum, G. Z., Teo, T. J., Yeo, S. H., Yang, G., Sitti, M.

Precision Engineering, 42, pages: 195-207, Elsevier, May 2015 (article)

Abstract
Flexure-based parallel mechanisms (FPMs) are a type of compliant mechanisms that consist of a rigid end-effector that is articulated by several parallel, flexible limbs (a.k.a. sub-chains). Existing design methods can enhance the FPMs’ dynamic and stiffness properties by conducting a size optimization on their sub-chains. A similar optimization process, however, was not performed for their sub-chains’ topology, and this may severely limit the benefits of a size optimization. Thus, this paper proposes to use a structural optimization approach to synthesize and optimize the topology, shape and size of the FPMs’ sub-chains. The benefits of this approach are demonstrated via the design and development of a planar X − Y − θz FPM. A prototype of this FPM was evaluated experimentally to have a large workspace of 1.2 mm × 1.2 mm × 6°, a fundamental natural frequency of 102 Hz, and stiffness ratios that are greater than 120. The achieved properties show significant improvement over existing 3-degrees-of-freedom compliant mechanisms that can deflect more than 0.5 mm and 0.5°. These compliant mechanisms typically have stiffness ratios that are less than 60 and a fundamental natural frequency that is less than 45 Hz.

pi

DOI [BibTex]

pi Lum, G. Z., Teo, T. J., Yeo, S. H., Yang, G., Sitti, M. Structural optimization for flexure-based parallel mechanisms–Towards achieving optimal dynamic and stiffness properties Precision Engineering, 42, pages: 195-207, Elsevier, May 2015 (article)

DOI [BibTex]

Thumb xl 1 s2.0 s0142961215003683 main
Controlled surface topography regulates collective 3D migration by epithelial–mesenchymal composite embryonic tissues

Song, J., Shawky, J. H., Kim, Y., Hazar, M., LeDuc, P. R., Sitti, M., Davidson, L. A.

Biomaterials, 58, pages: 1-9, Elsevier, April 2015 (article)

Abstract
Cells in tissues encounter a range of physical cues as they migrate. Probing single cell and collective migratory responses to physically defined three-dimensional (3D) microenvironments and the factors that modulate those responses are critical to understanding how tissue migration is regulated during development, regeneration, and cancer. One key physical factor that regulates cell migration is topography. Most studies on surface topography and cell mechanics have been carried out with single migratory cells, yet little is known about the spreading and motility response of 3D complex multi-cellular tissues to topographical cues. Here, we examine the response to complex topographical cues of microsurgically isolated tissue explants composed of epithelial and mesenchymal cell layers from naturally 3D organized embryos of the aquatic frog Xenopus laevis. We control topography using fabricated micropost arrays (MPAs) and investigate the collective 3D migration of these multi-cellular systems in these MPAs. We find that the topography regulates both collective and individual cell migration and that dense MPAs reduce but do not eliminate tissue spreading. By modulating cell size through the cell cycle inhibitor Mitomycin C or the spacing of the MPAs we uncover how 3D topographical cues disrupt collective cell migration. We find surface topography can direct both single cell motility and tissue spreading, altering tissue-scale processes that enable efficient conversion of single cell motility into collective movement.

pi

DOI [BibTex]

pi Song, J., Shawky, J. H., Kim, Y., Hazar, M., LeDuc, P. R., Sitti, M., Davidson, L. A. Controlled surface topography regulates collective 3D migration by epithelial–mesenchymal composite embryonic tissues Biomaterials, 58, pages: 1-9, Elsevier, April 2015 (article)

DOI [BibTex]

Thumb xl publications toc
Transfer Printing of Metallic Microstructures on Adhesion-Promoting Hydrogel Substrates

Wu, H., Sariola, V., Zhu, C., Zhao, J., Sitti, M., Bettinger, C. J.

Advanced Materials, 27(22):3398-3404, April 2015 (article)

Abstract
Fabrication schemes that integrate inorganic microstructures with hydrogel substrates are essential for advancing flexible electronics. A transfer printing process that is made possible through the design and synthesis of adhesion-promoting hydrogels as target substrates is reported. This fabrication technique may advance ultracompliant electronics by melding microfabricated structures with swollen hydrogel substrates.

pi

DOI [BibTex]

pi Wu, H., Sariola, V., Zhu, C., Zhao, J., Sitti, M., Bettinger, C. J. Transfer Printing of Metallic Microstructures on Adhesion-Promoting Hydrogel Substrates Advanced Materials, 27(22):3398-3404, April 2015 (article)

DOI [BibTex]

Thumb xl toc image patent
Dry adhesives and methods for making dry adhesives

Sitti, M., Murphy, M., Aksak, B.

March 2015, US Patent App. 14/625,162 (patent)

Abstract
Dry adhesives and methods for forming dry adhesives. A method of forming a dry adhesive structure on a substrate, comprises: forming a template backing layer of energy sensitive material on the substrate; forming a template layer of energy sensitive material on the template backing layer; exposing the template layer to a predetermined pattern of energy; removing a portion of the template layer related to the predetermined pattern of energy, and leaving a template structure formed from energy sensitive material and connected to the substrate via the template backing layer.

pi

[BibTex]

pi Sitti, M., Murphy, M., Aksak, B. Dry adhesives and methods for making dry adhesives March 2015, US Patent App. 14/625,162 (patent)

[BibTex]

Thumb xl publications toc
Biomedical applications of untethered mobile milli/microrobots

Sitti, M., Ceylan, H., Hu, W., Giltinan, J., Turan, M., Yim, S., Diller, E.

Proceedings of the IEEE, 103(2):205-224, IEEE, March 2015 (article)

Abstract
Untethered robots miniaturized to the length scale of millimeter and below attract growing attention for the prospect of transforming many aspects of health care and bioengineering. As the robot size goes down to the order of a single cell, previously inaccessible body sites would become available for high-resolution in situ and in vivo manipulations. This unprecedented direct access would enable an extensive range of minimally invasive medical operations. Here, we provide a comprehensive review of the current advances in biomedical untethered mobile milli/microrobots. We put a special emphasis on the potential impacts of biomedical microrobots in the near future. Finally, we discuss the existing challenges and emerging concepts associated with designing such a miniaturized robot for operation inside a biological environment for biomedical applications.

pi

DOI [BibTex]

pi Sitti, M., Ceylan, H., Hu, W., Giltinan, J., Turan, M., Yim, S., Diller, E. Biomedical applications of untethered mobile milli/microrobots Proceedings of the IEEE, 103(2):205-224, IEEE, March 2015 (article)

DOI [BibTex]

Thumb xl publications toc
Collective 3D Migration of Embryonic Epithelial Mesenchymal Composite Tissues are Regulated by Surface Topology

Song, J., Shawky, J., Kim, Y. T., Hazar, M., Sitti, M., LeDuc, P. R., Davidson, L. A.

Biophysical Journal, 108(2):455a, Elsevier, January 2015 (article)

Abstract
Cells in tissues encounter a range of physical cues as they migrate. Probing single cell and collective migratory responses to physically defined three-dimensional (3D) microenvironments and the factors that modulate those responses are critical to understanding how tissue migration is regulated during development, regeneration, and cancer. One key physical factor that regulates cell migration is topology. Most studies on surface topology and cell mechanics have been carried out with single migratory cells, yet little is known about the spreading and motility response of 3D complex multicellular tissues to topological cues. Here, we examine the behaviors of microsurgically isolated tissue explants composed of epithelial and mesenchymal cell layers from naturally 3D organized embryos of the aquatic frog Xenopus laevis to complex topological cues. We control topology using fabricated micropost arrays (MPAs) with different diameters (e.g., different spacing gaps) and investigate the collective 3D migration of these multicellular systems in these MPAs. Our topographical controlled approach for cellular application enables us to achieve a high degree of control over micropost positioning and geometry via simple, accurate, and repeatable microfabrication processes. We find that the topology regulates both collective and individual cell migration and that dense MPAs reduce but do not eliminate tissue spreading. By modulating cell size through the cell cycle inhibitor Mitomycin C or the spacing within MPAs we discover a role for topology in disrupting collective enhancement of cell migration. We find 3D topological cues can direct both single cell motility and tissue spreading, altering tissue-scale processes that enable efficient conversion of single cell motility into collective movement.

pi

DOI [BibTex]

pi Song, J., Shawky, J., Kim, Y. T., Hazar, M., Sitti, M., LeDuc, P. R., Davidson, L. A. Collective 3D Migration of Embryonic Epithelial Mesenchymal Composite Tissues are Regulated by Surface Topology Biophysical Journal, 108(2):455a, Elsevier, January 2015 (article)

DOI [BibTex]

Thumb xl publications toc
Three-dimensional heterogeneous assembly of coded microgels using an untethered mobile microgripper

Chung, S. E., Dong, X., Sitti, M.

Lab on a Chip, 15(7):1667-1676, Royal Society of Chemistry, January 2015 (article)

Abstract
Three-dimensional (3D) heterogeneous assembly of coded microgels in enclosed aquatic environments is demonstrated using a remotely actuated and controlled magnetic microgripper by a customized electromagnetic coil system. The microgripper uses different ‘stick–slip’ and ‘rolling’ locomotion in 2D and also levitation in 3D by magnetic gradient-based pulling force. This enables the microrobot to precisely manipulate each microgel by controlling its position and orientation in all x–y–z directions. Our microrobotic assembly method broke the barrier of limitation on the number of assembled microgel layers, because it enabled precise 3D levitation of the microgripper. We used the gripper to assemble microgels that had been coded with different colours and shapes onto prefabricated polymeric microposts. This eliminates the need for extra secondary cross-linking to fix the final construct. We demonstrated assembly of microgels on a single micropost up to ten layers. By increasing the number and changing the distribution of the posts, complex heterogeneous microsystems were possible to construct in 3D.

pi

DOI Project Page [BibTex]

pi Chung, S. E., Dong, X., Sitti, M. Three-dimensional heterogeneous assembly of coded microgels using an untethered mobile microgripper Lab on a Chip, 15(7):1667-1676, Royal Society of Chemistry, January 2015 (article)

DOI Project Page [BibTex]

Thumb xl publications toc
Integrating mechanism synthesis and topological optimization technique for stiffness-oriented design of a three degrees-of-freedom flexure-based parallel mechanism

Lum, G. Z., Teo, T. J., Yang, G., Yeo, S. H., Sitti, M.

Precision Engineering, 39, pages: 125-133, Elsevier, January 2015 (article)

Abstract
This paper introduces a new design approach to synthesize multiple degrees-of-freedom (DOF) flexure-based parallel mechanism (FPM). Termed as an integrated design approach, it is a systematic design methodology, which integrates both classical mechanism synthesis and modern topology optimization technique, to deliver an optimized multi-DOF FPM. This design approach is separated into two levels. At sub-chain level, a novel topology optimization technique, which uses the classical linkage mechanisms as DNA seeds, is used to synthesize the compliant joints or limbs. At configuration level, the optimal compliant joints are used to form the parallel limbs of the multi-DOF FPM and another stage of optimization was conducted to determine the optimal space distribution between these compliant joints so as to generate a multi-DOF FPM with optimized stiffness characteristic. In this paper, the design of a 3-DOF planar motion FPM was used to demonstrate the effectiveness and accuracy of this proposed design approach.

pi

DOI [BibTex]

Thumb xl publications toc
Actively controlled fibrillar friction surfaces

Marvi, H, Han, Y, Sitti, M

Applied Physics Letters, 106(5):051602, AIP Publishing, January 2015 (article)

Abstract
In this letter, we propose a technique by which we can actively adjust frictional properties of elastic fibrillar structures in different directions. Using a mesh attached to a two degree-of-freedom linear stage, we controlled the active length and the tilt angle of fibers, independently. Thus, we were able to achieve desired levels of friction forces in different directions and significantly improve passive friction anisotropies observed in the same fiber arrays. The proposed technique would allow us to readily control the friction anisotropy and the friction magnitude of fibrillar structures in any planar direction.

pi

DOI [BibTex]

pi Marvi, H, Han, Y, Sitti, M Actively controlled fibrillar friction surfaces Applied Physics Letters, 106(5):051602, AIP Publishing, January 2015 (article)

DOI [BibTex]

no image
Isosteric heat of hydrogen adsorption on MOFs: comparison between adsorption calorimetry, sorption isosteric metod, and analytical models

Kloutse, A. F., Zacharia, R., Cossement, D., Chahine, R., Balderas-Xicohténcatl, R., Oh, H., Streppel, B., Schlichtenmayer, M., Hirscher, M.

{Applied Physics A}, 121(4):1417-1424, Springer-Verlag Heidelberg, Heidelberg, 2015 (article)

mms

DOI [BibTex]

mms Kloutse, A. F., Zacharia, R., Cossement, D., Chahine, R., Balderas-Xicohténcatl, R., Oh, H., Streppel, B., Schlichtenmayer, M., Hirscher, M. Isosteric heat of hydrogen adsorption on MOFs: comparison between adsorption calorimetry, sorption isosteric metod, and analytical models {Applied Physics A}, 121(4):1417-1424, Springer-Verlag Heidelberg, Heidelberg, 2015 (article)

DOI [BibTex]

no image
Time-resolved imaging of pulse-induced magnetization reversal with a microwave assist field

Rao, S., Rhensius, J., Bisig, A., Mawass, M.-A., Weigand, M., Kläui, M., Bhatia, C. S., Yang, H.

{Scientific Reports}, 5, Nature Publishing Group, London, UK, 2015 (article)

mms

DOI [BibTex]

mms Rao, S., Rhensius, J., Bisig, A., Mawass, M.-A., Weigand, M., Kläui, M., Bhatia, C. S., Yang, H. Time-resolved imaging of pulse-induced magnetization reversal with a microwave assist field {Scientific Reports}, 5, Nature Publishing Group, London, UK, 2015 (article)

DOI [BibTex]

no image
XMCD studies of thin Co films on BaTiO3

Welke, M., Gräfe, J., Govind, R. K., Babu, V. H., Trautmann, M., Schindler, K., Denecke, R.

{Journal of Physics: Condensed Matter}, 27(32), IOP Publishing, Bristol, UK, 2015 (article)

mms

DOI [BibTex]

mms Welke, M., Gräfe, J., Govind, R. K., Babu, V. H., Trautmann, M., Schindler, K., Denecke, R. XMCD studies of thin Co films on BaTiO3 {Journal of Physics: Condensed Matter}, 27(32), IOP Publishing, Bristol, UK, 2015 (article)

DOI [BibTex]

no image
Combined FORC and x-ray microscopy study of magnetisation reversal in antidot lattices

Gräfe, J., Haering, F., Stahl, C., Weigand, M., Skripnik, M., Nowak, U., Ziemann, P., Wiedwald, U., Schütz, G., Goering, E.

In IEEE International Magnetics Conference (INTERMAG 2015), IEEE, Beijing, China, 2015 (inproceedings)

mms

DOI Project Page Project Page [BibTex]

mms Gräfe, J., Haering, F., Stahl, C., Weigand, M., Skripnik, M., Nowak, U., Ziemann, P., Wiedwald, U., Schütz, G., Goering, E. Combined FORC and x-ray microscopy study of magnetisation reversal in antidot lattices In IEEE International Magnetics Conference (INTERMAG 2015), IEEE, Beijing, China, 2015 (inproceedings)

DOI Project Page Project Page [BibTex]

no image
Low temperature X-ray imaging of magnetic flux patterns in high temperature superconductors

Stahl, C., Ruoß, S., Weigand, M., Bechtel, M., Schütz, G., Albrecht, J.

{Journal of Applied Physics}, 117(17), AIP Publishing, New York, NY, 2015 (article)

mms

DOI [BibTex]

mms Stahl, C., Ruoß, S., Weigand, M., Bechtel, M., Schütz, G., Albrecht, J. Low temperature X-ray imaging of magnetic flux patterns in high temperature superconductors {Journal of Applied Physics}, 117(17), AIP Publishing, New York, NY, 2015 (article)

DOI [BibTex]

no image
Local control of domain wall dynamics in ferromagnetic rings

Richter, K., Mawass, M., Krone, A., Krüger, B., Weigand, M., Stoll, H., Schütz, G., Kläui, M.

In IEEE International Magnetics Conference (INTERMAG 2015), IEEE, Beijing, China, 2015 (inproceedings)

mms

DOI [BibTex]

mms Richter, K., Mawass, M., Krone, A., Krüger, B., Weigand, M., Stoll, H., Schütz, G., Kläui, M. Local control of domain wall dynamics in ferromagnetic rings In IEEE International Magnetics Conference (INTERMAG 2015), IEEE, Beijing, China, 2015 (inproceedings)

DOI [BibTex]

no image
Formation of a quasi-solid structure by intercalated noble gas atoms in pores of CuI-MFU-4l metal-organic framework

Magdysyuk, O. V., Denysenko, D., Weinrauch, I., Volkmer, D., Hirscher, M., Dinnebier, R. E.

{Chemical Communications}, 51(4):714-717, Royal Society of Chemistry, Cambridge, UK, 2015 (article)

mms

DOI [BibTex]

mms Magdysyuk, O. V., Denysenko, D., Weinrauch, I., Volkmer, D., Hirscher, M., Dinnebier, R. E. Formation of a quasi-solid structure by intercalated noble gas atoms in pores of CuI-MFU-4l metal-organic framework {Chemical Communications}, 51(4):714-717, Royal Society of Chemistry, Cambridge, UK, 2015 (article)

DOI [BibTex]

no image
Burst-mode manipulation of magnonic vortex crystals

Hänze, M., Adolff, C. F., Weigand, M., Meier, G.

{Physical Review B}, 91(10), American Physical Society, Woodbury, NY, 2015 (article)

mms

DOI [BibTex]

mms Hänze, M., Adolff, C. F., Weigand, M., Meier, G. Burst-mode manipulation of magnonic vortex crystals {Physical Review B}, 91(10), American Physical Society, Woodbury, NY, 2015 (article)

DOI [BibTex]

no image
Strukturelle und spektroskopische Eigenschaften epitaktischer FeMn/Co Exchange-Bias-Systeme

Schmidt, M.

Universität Stuttgart, Stuttgart, 2015 (phdthesis)

mms

link (url) DOI [BibTex]

no image
Fabrication and X-ray testing of true kinoform lenses with high efficiencies

Keskinbora, K., Sanli, U., Grévent, C., Schütz, G.

{Proceedings of SPIE}, 9592, SPIE, Bellingham, Washington, 2015 (article)

mms

DOI [BibTex]

mms Keskinbora, K., Sanli, U., Grévent, C., Schütz, G. Fabrication and X-ray testing of true kinoform lenses with high efficiencies {Proceedings of SPIE}, 9592, SPIE, Bellingham, Washington, 2015 (article)

DOI [BibTex]

no image
Ultraschnelles Vortexkernschalten

Noske, M.

Universität Stuttgart, Stuttgart (und Cuvillier Verlag, Göttingen), 2015 (phdthesis)

mms

[BibTex]

mms Noske, M. Ultraschnelles Vortexkernschalten Universität Stuttgart, Stuttgart (und Cuvillier Verlag, Göttingen), 2015 (phdthesis)

[BibTex]

no image
Investigations of unusual hard magnetic MnBi LTP phase, utilizing temperature dependent SQUID-FORC

Muralidhar, Shreyas

Universität Stuttgart, Stuttgart, 2015 (mastersthesis)

mms

[BibTex]

mms Muralidhar, Shreyas Investigations of unusual hard magnetic MnBi LTP phase, utilizing temperature dependent SQUID-FORC Universität Stuttgart, Stuttgart, 2015 (mastersthesis)

[BibTex]

no image
Magnetische Röntgenmikroskopie an Hochtemperatur-Supraleitern

Stahl, C.

Universität Stuttgart, Stuttgart (und Cuvillier Verlag, Göttingen), 2015 (phdthesis)

mms

[BibTex]

mms Stahl, C. Magnetische Röntgenmikroskopie an Hochtemperatur-Supraleitern Universität Stuttgart, Stuttgart (und Cuvillier Verlag, Göttingen), 2015 (phdthesis)

[BibTex]

no image
Focused ion beam micromachining enables novel optics for X-ray microscopy

Keskinbora, K., Sanli, U., Grévent, C., Hirscher, M., Schütz, G.

{Microscopy and Microanalysis}, 21(Suppl 3):1983-1984, Springer-Verlag New York, New York, NY, 2015 (article)

mms

DOI [BibTex]

mms Keskinbora, K., Sanli, U., Grévent, C., Hirscher, M., Schütz, G. Focused ion beam micromachining enables novel optics for X-ray microscopy {Microscopy and Microanalysis}, 21(Suppl 3):1983-1984, Springer-Verlag New York, New York, NY, 2015 (article)

DOI [BibTex]

no image
Selectable nanopattern arrays for nanolithographic imprint and etch-mask applications

Jeong, H., Mark, A. G., Lee, T., Son, K., Chen, W., Alarcón-Correa, M., Kim, I., Schütz, G., Fischer, P.

{Advanced Science}, 2(2), Wiley-VCH, Weinheim, 2015 (article)

mms

DOI [BibTex]

mms Jeong, H., Mark, A. G., Lee, T., Son, K., Chen, W., Alarcón-Correa, M., Kim, I., Schütz, G., Fischer, P. Selectable nanopattern arrays for nanolithographic imprint and etch-mask applications {Advanced Science}, 2(2), Wiley-VCH, Weinheim, 2015 (article)

DOI [BibTex]

no image
Grain boundaries as a source of ferromagnetism and increased solubility of Ni in nanograined ZnO

Straumal, B. B., Mazilkin, A. A., Protasova, S. G., Stakhanova, S. V., Straumal, P. B., Bulatov, M. F., Schütz, G., Tietze, T., Goering, E., Baretzky, B.

{Reviews on Advanced Materials Science}, 41, pages: 61-71, 2015 (article)

mms

[BibTex]

mms Straumal, B. B., Mazilkin, A. A., Protasova, S. G., Stakhanova, S. V., Straumal, P. B., Bulatov, M. F., Schütz, G., Tietze, T., Goering, E., Baretzky, B. Grain boundaries as a source of ferromagnetism and increased solubility of Ni in nanograined ZnO {Reviews on Advanced Materials Science}, 41, pages: 61-71, 2015 (article)

[BibTex]

no image
Gyrational modes of benzenelike magnetic vortex molecules

Adolff, C. F., Hänze, M., Pues, M., Weigand, M., Meier, G.

{Physical Review B}, 92(2), American Physical Society, Woodbury, NY, 2015 (article)

mms

DOI [BibTex]

mms Adolff, C. F., Hänze, M., Pues, M., Weigand, M., Meier, G. Gyrational modes of benzenelike magnetic vortex molecules {Physical Review B}, 92(2), American Physical Society, Woodbury, NY, 2015 (article)

DOI [BibTex]

no image
"Job-Sharing" storage of hydrogen in Ru/Li2O nanocomposites

Fu, L., Tang, K., Oh, H., Kandavel, M., Bräuniger, T., Vinod Chandran, C., Menzel, A., Hirscher, M., Samuelis, D., Maier, J.

{Nano Letters}, 15(6):4170-4175, American Chemical Society, Washington, DC, 2015 (article)

mms

DOI [BibTex]

mms Fu, L., Tang, K., Oh, H., Kandavel, M., Bräuniger, T., Vinod Chandran, C., Menzel, A., Hirscher, M., Samuelis, D., Maier, J. "Job-Sharing" storage of hydrogen in Ru/Li2O nanocomposites {Nano Letters}, 15(6):4170-4175, American Chemical Society, Washington, DC, 2015 (article)

DOI [BibTex]

no image
Overview of the multilayer-Fresnel zone plate and the kinoform lens development at MPI for Intelligent Systems

Sanli, U., Keskinbora, K., Grévent, C., Schütz, G.

{Proceedings of SPIE}, 9510, SPIE, Bellingham, Washington, 2015 (article)

mms

DOI [BibTex]

no image
Transition matrix elements for electron-phonon scattering: Phenomenological theory and ab initio electron theory

Illg, C., Haag, M., Müller, B. Y., Czycholl, G., Fähnle, M.

{Physical Review B}, 92(19), American Physical Society, Woodbury, NY, 2015 (article)

mms

DOI [BibTex]

mms Illg, C., Haag, M., Müller, B. Y., Czycholl, G., Fähnle, M. Transition matrix elements for electron-phonon scattering: Phenomenological theory and ab initio electron theory {Physical Review B}, 92(19), American Physical Society, Woodbury, NY, 2015 (article)

DOI [BibTex]

no image
Phase evolution in single-crystalline LiFePO4 followed by in situ scanning X-ray microscopy of a micrometre-sized battery

Ohmer, N., Fenk, B., Samuelis, D., Chen, C., Maier, J., Weigand, M., Goering, E., Schütz, G.

{Nature Communications}, 6, Nature Publishing Group, London, 2015 (article)

mms

DOI [BibTex]

mms Ohmer, N., Fenk, B., Samuelis, D., Chen, C., Maier, J., Weigand, M., Goering, E., Schütz, G. Phase evolution in single-crystalline LiFePO4 followed by in situ scanning X-ray microscopy of a micrometre-sized battery {Nature Communications}, 6, Nature Publishing Group, London, 2015 (article)

DOI [BibTex]

no image
Nitrogen-rich covalent triazine frameworks as high-performance platforms for selective carbon capture and storage

Hug, S., Stegbauer, L., Oh, H., Hirscher, M., Lotsch, B. V.

{Chemistry of Materials}, 27(23):8001-8010, American Chemical Society, Washington, D.C., 2015 (article)

mms

DOI [BibTex]

mms Hug, S., Stegbauer, L., Oh, H., Hirscher, M., Lotsch, B. V. Nitrogen-rich covalent triazine frameworks as high-performance platforms for selective carbon capture and storage {Chemistry of Materials}, 27(23):8001-8010, American Chemical Society, Washington, D.C., 2015 (article)

DOI [BibTex]

no image
Multilayer Fresnel zone plates for X-ray microscopy

Sanli, U. T., Keskinbora, K., Grévent, C., Szeghalmi, A., Knez, M., Schütz, G.

{Microscopy and Microanalysis}, 21(Suppl 3):1987-1988, Springer-Verlag New York, New York, NY, 2015 (article)

mms

DOI [BibTex]

mms Sanli, U. T., Keskinbora, K., Grévent, C., Szeghalmi, A., Knez, M., Schütz, G. Multilayer Fresnel zone plates for X-ray microscopy {Microscopy and Microanalysis}, 21(Suppl 3):1987-1988, Springer-Verlag New York, New York, NY, 2015 (article)

DOI [BibTex]

no image
Interfacial dominated ferromagnetism in nanograined ZnO: a \muSR and DFT study

Tietze, T., Audehm, P., Chen, Y., Schütz, G., Straumal, B. B., Protasova, S. G., Mazilkin, A. A., Straumal, P. B., Prokscha, T., Luetkens, H., Salman, Z., Suter, A., Baretzky, B., Fink, K., Wenzel, W., Danilov, D., Goering, E.

{Scientific Reports}, 5, pages: 8871-8876, Nature Publishing Group, London, UK, 2015 (article)

mms

DOI [BibTex]

mms Tietze, T., Audehm, P., Chen, Y., Schütz, G., Straumal, B. B., Protasova, S. G., Mazilkin, A. A., Straumal, P. B., Prokscha, T., Luetkens, H., Salman, Z., Suter, A., Baretzky, B., Fink, K., Wenzel, W., Danilov, D., Goering, E. Interfacial dominated ferromagnetism in nanograined ZnO: a \muSR and DFT study {Scientific Reports}, 5, pages: 8871-8876, Nature Publishing Group, London, UK, 2015 (article)

DOI [BibTex]

no image
Preparation of a ferromagnetic barrier in YBa2Cu3O7-delta thinner than the coherence length

Soltan, S., Albrecht, J., Goering, E., Schütz, G., Mustafa, L., Keimer, B., Habermeier, H.

{Journal of Applied Physics}, 118(22), AIP Publishing, New York, NY, 2015 (article)

mms

DOI [BibTex]

mms Soltan, S., Albrecht, J., Goering, E., Schütz, G., Mustafa, L., Keimer, B., Habermeier, H. Preparation of a ferromagnetic barrier in YBa2Cu3O7-delta thinner than the coherence length {Journal of Applied Physics}, 118(22), AIP Publishing, New York, NY, 2015 (article)

DOI [BibTex]

no image
Microanalytical methods for in-situ high-resolution analysis of rock varnish at the micrometer to nanometer scale

Macholdt, D. S., Jochum, K. P., Pöhlker, C., Stoll, B., Weis, U., Weber, B., Müller, M., Kapl, M., Buhre, S., Kilcoyne, A. L. D., Weigand, M., Scholz, D., Al-Amri, A. M., Andreae, M. O.

{Chemical Geology}, 411, pages: 57-68, Elsevier, Amsterdam, 2015 (article)

mms

DOI [BibTex]

mms Macholdt, D. S., Jochum, K. P., Pöhlker, C., Stoll, B., Weis, U., Weber, B., Müller, M., Kapl, M., Buhre, S., Kilcoyne, A. L. D., Weigand, M., Scholz, D., Al-Amri, A. M., Andreae, M. O. Microanalytical methods for in-situ high-resolution analysis of rock varnish at the micrometer to nanometer scale {Chemical Geology}, 411, pages: 57-68, Elsevier, Amsterdam, 2015 (article)

DOI [BibTex]

no image
Chemical composition, microstructure, and hygroscopic properties of aerosol particles at the Zotino Tall Tower Observatory (ZOTTO), Siberia, during a summer campaign

Mikhailov, E. F., Mironov, G. N., Pöhlker, C., Chi, X., Krüger, M., Shiraiwa, M., Förster, J., Pöschl, U., Vlasenko, S. S., Ryshkevich, T. I., Weigand, M., Kilcoyne, A. L. D., Andreae, M.

{Atmospheric Chemistry and Physics}, 15(15):8847-8869, European Geosciences Union, Katlenburg-Lindau, Germany, 2015 (article)

mms

DOI [BibTex]

mms Mikhailov, E. F., Mironov, G. N., Pöhlker, C., Chi, X., Krüger, M., Shiraiwa, M., Förster, J., Pöschl, U., Vlasenko, S. S., Ryshkevich, T. I., Weigand, M., Kilcoyne, A. L. D., Andreae, M. Chemical composition, microstructure, and hygroscopic properties of aerosol particles at the Zotino Tall Tower Observatory (ZOTTO), Siberia, during a summer campaign {Atmospheric Chemistry and Physics}, 15(15):8847-8869, European Geosciences Union, Katlenburg-Lindau, Germany, 2015 (article)

DOI [BibTex]

no image
Orbital reflectometry of PrNiO3/PrAlO3 superlattices

Wu, M., Benckiser, E., Audehm, P., Goering, E., Wochner, P., Christiani, G., Logvenov, G., Habermeier, H., Keimer, B.

{Physical Review B}, 91(19), American Physical Society, Woodbury, NY, 2015 (article)

mms

DOI [BibTex]

mms Wu, M., Benckiser, E., Audehm, P., Goering, E., Wochner, P., Christiani, G., Logvenov, G., Habermeier, H., Keimer, B. Orbital reflectometry of PrNiO3/PrAlO3 superlattices {Physical Review B}, 91(19), American Physical Society, Woodbury, NY, 2015 (article)

DOI [BibTex]

no image
Dynamic domain wall chirality rectification by rotating magnetic fields

Bisig, A., Mawass, M., Stärk, M., Moutafis, C., Rhensius, J., Heidler, J., Gliga, S., Weigand, M., Tyliszczak, T., Van Waeyenberge, B., Stoll, H., Schütz, G., Kläui, M.

{Applied Physics Letters}, 106(12), American Institute of Physics, Melville, NY, 2015 (article)

mms

DOI [BibTex]

mms Bisig, A., Mawass, M., Stärk, M., Moutafis, C., Rhensius, J., Heidler, J., Gliga, S., Weigand, M., Tyliszczak, T., Van Waeyenberge, B., Stoll, H., Schütz, G., Kläui, M. Dynamic domain wall chirality rectification by rotating magnetic fields {Applied Physics Letters}, 106(12), American Institute of Physics, Melville, NY, 2015 (article)

DOI [BibTex]

no image
Ultrafast demagnetization after laser pulse irradiation in Ni: Ab-initio electron-phonon scattering and phase space calculations

Illg, C., Haag, M., Fähnle, M.

In Ultrafast Magnetism I. Proceedings of the International Conference UMC 2013, 159, pages: 131-133, Springer Proceedings in Physics, Springer, Strasbourg, 2015 (inproceedings)

mms

DOI [BibTex]

mms Illg, C., Haag, M., Fähnle, M. Ultrafast demagnetization after laser pulse irradiation in Ni: Ab-initio electron-phonon scattering and phase space calculations In Ultrafast Magnetism I. Proceedings of the International Conference UMC 2013, 159, pages: 131-133, Springer Proceedings in Physics, Springer, Strasbourg, 2015 (inproceedings)

DOI [BibTex]

no image
Imaging spin dynamics on the nanoscale using X-ray microscopy

Stoll, H., Noske, M., Weigand, M., Richter, K., Krüger, B., Reeve, R. M., Hänze, M., Adolff, C. F., Stein, F., Meier, G., Kläui, M., Schütz, G.

{Frontiers in Physics}, 3, Frontiers Media, Lausanne, 2015 (article)

mms

DOI [BibTex]

mms Stoll, H., Noske, M., Weigand, M., Richter, K., Krüger, B., Reeve, R. M., Hänze, M., Adolff, C. F., Stein, F., Meier, G., Kläui, M., Schütz, G. Imaging spin dynamics on the nanoscale using X-ray microscopy {Frontiers in Physics}, 3, Frontiers Media, Lausanne, 2015 (article)

DOI [BibTex]

no image
Voltage-induced magnetic manipulation of a microstructured iron gold multilayer system

Sittig, Robert

Universität Stuttgart, Stuttgart, 2015 (mastersthesis)

mms

[BibTex]

mms Sittig, Robert Voltage-induced magnetic manipulation of a microstructured iron gold multilayer system Universität Stuttgart, Stuttgart, 2015 (mastersthesis)

[BibTex]