Header logo is


2016


no image
Predictive and Self Triggering for Event-based State Estimation

Trimpe, S.

In Proceedings of the 55th IEEE Conference on Decision and Control (CDC), pages: 3098-3105, Las Vegas, NV, USA, December 2016 (inproceedings)

am ics

arXiv PDF DOI Project Page [BibTex]

2016


arXiv PDF DOI Project Page [BibTex]


no image
Qualitative User Reactions to a Hand-Clapping Humanoid Robot

Fitter, N. T., Kuchenbecker, K. J.

In Social Robotics: 8th International Conference, ICSR 2016, Kansas City, MO, USA, November 1-3, 2016 Proceedings, 9979, pages: 317-327, Lecture Notes in Artificial Intelligence, Springer International Publishing, November 2016, Oral presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Designing and Assessing Expressive Open-Source Faces for the Baxter Robot

Fitter, N. T., Kuchenbecker, K. J.

In Social Robotics: 8th International Conference, ICSR 2016, Kansas City, MO, USA, November 1-3, 2016 Proceedings, 9979, pages: 340-350, Lecture Notes in Artificial Intelligence, Springer International Publishing, November 2016, Oral presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Rhythmic Timing in Playful Human-Robot Social Motor Coordination

Fitter, N. T., Hawkes, D. T., Kuchenbecker, K. J.

In Social Robotics: 8th International Conference, ICSR 2016, Kansas City, MO, USA, November 1-3, 2016 Proceedings, 9979, pages: 296-305, Lecture Notes in Artificial Intelligence, Springer International Publishing, November 2016, Oral presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Using IMU Data to Demonstrate Hand-Clapping Games to a Robot

Fitter, N. T., Kuchenbecker, K. J.

In Proceedings of the IEEE/RSJ International Conference on Intelligent Robots and Systems, pages: 851 - 856, October 2016, Interactive presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Dynamical self-consistency leads to behavioral development and emergent social interactions in robots.

Der, R., Martius, G.

In Proc. IEEE Int. Conf. on Development and Learning and Epigenetic Robotics, pages: 49-56, IEEE, September 2016, in press (inproceedings)

al

DOI [BibTex]

DOI [BibTex]


no image
ProtonPack: A Visuo-Haptic Data Acquisition System for Robotic Learning of Surface Properties

Burka, A., Hu, S., Helgeson, S., Krishnan, S., Gao, Y., Hendricks, L. A., Darrell, T., Kuchenbecker, K. J.

In Proceedings of the IEEE International Conference on Multisensor Fusion and Integration for Intelligent Systems (MFI), pages: 58-65, 2016, Oral presentation given by Burka (inproceedings)

hi

Project Page [BibTex]

Project Page [BibTex]


no image
Equipping the Baxter Robot with Human-Inspired Hand-Clapping Skills

Fitter, N. T., Kuchenbecker, K. J.

In Proceedings of the IEEE International Symposium on Robot and Human Interactive Communication (RO-MAN), pages: 105-112, 2016 (inproceedings)

hi

[BibTex]

[BibTex]


no image
Comparison of vibro-acoustic performance metrics in the design and optimization of stiffened composite fuselages

Serhat, G., Basdogan, I.

In Proceedings of International Congress and Exposition of Noise Control Engineering (INTER-NOISE), Hamburg, Germany, August 2016 (inproceedings)

Abstract
In this paper, a comparison of preliminary design methodologies for optimization of stiffened, fiber-reinforced composite fuselages for vibro-acoustic requirements is presented. Fuselage stiffness properties are modelled using lamination parameters and their effect on the vibro-acoustic performance is investigated using two different approaches. First method, only considers the structural model in order to explore the effect of design variables on fuselage vibrations. The simplified estimation of the acoustic behavior without considering fluid-structure interaction brings certain advantages such as reduced modelling effort and computational cost. In this case, the performance metric is chosen as equivalent radiated power (ERP) which is a well-known criterion in the prediction of structure-born noise. Second method, utilizes coupled vibro-acoustic models to predict the sound pressure levels (SPL) inside the fuselage. ERP is calculated both for bay panels and fuselage section and then compared with the SPL results. The response surfaces of each metric are determined as a function of lamination parameters and their overall difference is quantified. ERP approach proves its merit provided that a sufficiently accurate model is used. The results demonstrate the importance of the simplifications made in the modelling and the selection of analysis approach in vibro-acoustic design of fuselages.

hi

[BibTex]

[BibTex]


no image
Reproducing a Laser Pointer Dot on a Secondary Projected Screen

Hu, S., Kuchenbecker, K. J.

In Proceedings of the IEEE International Conference on Advanced Intelligent Mechatronics (AIM), pages: 1645-1650, 2016, Oral presentation given by Hu (inproceedings)

hi

[BibTex]

[BibTex]


no image
Effect of Aspect Ratio and Boundary Conditions on the Eigenfrequency Optimization of Composite Panels Using Lamination Parameters

Serhat, G., Basdogan, I.

In Proceedings of the ASMO UK International Conference on Numerical Optimisation Methods for Engineering Design, pages: 160–168, Munich, Germany, July 2016 (inproceedings)

Abstract
Eigenfrequency optimization of laminated composite panels is a common engineering problem. This process mostly involves designing stiffness properties of the structure. Optimal results can differ significantly depending on the values of the model parameters and the metrics used for the optimization. Building the know-how on this matter is crucial for choosing the appropriate design methodologies as well as validation and justification of prospective results. In this paper, effects of aspect ratio and boundary conditions on eigenfrequency optimization of composite panels by altering stiffness properties are investigated. Lamination parameters are chosen as design variables which are used in the modeling of stiffness tensors. This technique enables representation of overall stiffness characteristics and provides a convex design space. Fundamental frequency and difference between fundamental and second natural frequencies are maximized as design objectives. Optimization studies incorporating different models and responses are performed. Optimal lamination parameters and response values are provided for each case and the effects of model parameters on the solutions are quantified. The results indicate that trends of the optima change for different aspect ratio ranges and boundary conditions. Moreover, convergence occurs beyond certain critical values of the model parameters which may cause an optimization study to be redundant.

hi

[BibTex]

[BibTex]


Robust Gaussian Filtering using a Pseudo Measurement
Robust Gaussian Filtering using a Pseudo Measurement

Wüthrich, M., Garcia Cifuentes, C., Trimpe, S., Meier, F., Bohg, J., Issac, J., Schaal, S.

In Proceedings of the American Control Conference (ACC), Boston, MA, USA, July 2016 (inproceedings)

Abstract
Most widely-used state estimation algorithms, such as the Extended Kalman Filter and the Unscented Kalman Filter, belong to the family of Gaussian Filters (GF). Unfortunately, GFs fail if the measurement process is modelled by a fat-tailed distribution. This is a severe limitation, because thin-tailed measurement models, such as the analytically-convenient and therefore widely-used Gaussian distribution, are sensitive to outliers. In this paper, we show that mapping the measurements into a specific feature space enables any existing GF algorithm to work with fat-tailed measurement models. We find a feature function which is optimal under certain conditions. Simulation results show that the proposed method allows for robust filtering in both linear and nonlinear systems with measurements contaminated by fat-tailed noise.

am ics

Web link (url) DOI Project Page [BibTex]

Web link (url) DOI Project Page [BibTex]


no image
Multi-objective optimization of stiffened, fiber-reinforced composite fuselages for mechanical and vibro-acoustic requirements

Serhat, G., Faria, T. G., Basdogan, I.

In Proceedings of AIAA/ISSMO Multidisciplinary Analysis and Optimization Conference, Washington, USA, June 2016 (inproceedings)

Abstract
In this paper, a preliminary design methodology for optimization of stiffened, fiber-reinforced composite fuselages for combined mechanical and vibro-acoustic requirements is presented. Laminate stiffness distributions are represented using the method called lamination parameters which is known to provide a convex solution space. Single-objective and multi-objective optimization studies are carried out in order to find optimal stiffness distributions. Performance metrics for acoustical behavior are chosen as maximum fundamental frequency and minimum equivalent radiated power. The mechanical performance metric is chosen as the maximum stiffness. The results show that the presented methodology works effectively and it can be used to improve load-carrying and acoustical performances simultaneously.

hi

DOI [BibTex]

DOI [BibTex]


Automatic LQR Tuning Based on Gaussian Process Global Optimization
Automatic LQR Tuning Based on Gaussian Process Global Optimization

Marco, A., Hennig, P., Bohg, J., Schaal, S., Trimpe, S.

In Proceedings of the IEEE International Conference on Robotics and Automation (ICRA), pages: 270-277, IEEE, IEEE International Conference on Robotics and Automation, May 2016 (inproceedings)

Abstract
This paper proposes an automatic controller tuning framework based on linear optimal control combined with Bayesian optimization. With this framework, an initial set of controller gains is automatically improved according to a pre-defined performance objective evaluated from experimental data. The underlying Bayesian optimization algorithm is Entropy Search, which represents the latent objective as a Gaussian process and constructs an explicit belief over the location of the objective minimum. This is used to maximize the information gain from each experimental evaluation. Thus, this framework shall yield improved controllers with fewer evaluations compared to alternative approaches. A seven-degree- of-freedom robot arm balancing an inverted pole is used as the experimental demonstrator. Results of a two- and four- dimensional tuning problems highlight the method’s potential for automatic controller tuning on robotic platforms.

am ics pn

Video - Automatic LQR Tuning Based on Gaussian Process Global Optimization - ICRA 2016 Video - Automatic Controller Tuning on a Two-legged Robot PDF DOI Project Page [BibTex]

Video - Automatic LQR Tuning Based on Gaussian Process Global Optimization - ICRA 2016 Video - Automatic Controller Tuning on a Two-legged Robot PDF DOI Project Page [BibTex]


Depth-based Object Tracking Using a Robust Gaussian Filter
Depth-based Object Tracking Using a Robust Gaussian Filter

Issac, J., Wüthrich, M., Garcia Cifuentes, C., Bohg, J., Trimpe, S., Schaal, S.

In Proceedings of the IEEE International Conference on Robotics and Automation (ICRA) 2016, IEEE, IEEE International Conference on Robotics and Automation, May 2016 (inproceedings)

Abstract
We consider the problem of model-based 3D- tracking of objects given dense depth images as input. Two difficulties preclude the application of a standard Gaussian filter to this problem. First of all, depth sensors are characterized by fat-tailed measurement noise. To address this issue, we show how a recently published robustification method for Gaussian filters can be applied to the problem at hand. Thereby, we avoid using heuristic outlier detection methods that simply reject measurements if they do not match the model. Secondly, the computational cost of the standard Gaussian filter is prohibitive due to the high-dimensional measurement, i.e. the depth image. To address this problem, we propose an approximation to reduce the computational complexity of the filter. In quantitative experiments on real data we show how our method clearly outperforms the standard Gaussian filter. Furthermore, we compare its performance to a particle-filter-based tracking method, and observe comparable computational efficiency and improved accuracy and smoothness of the estimates.

am ics

Video Bayesian Object Tracking Library Bayesian Filtering Framework Object Tracking Dataset link (url) DOI Project Page [BibTex]

Video Bayesian Object Tracking Library Bayesian Filtering Framework Object Tracking Dataset link (url) DOI Project Page [BibTex]


no image
Communication Rate Analysis for Event-based State Estimation

(Best student paper finalist)

Ebner, S., Trimpe, S.

In Proceedings of the 13th International Workshop on Discrete Event Systems, May 2016 (inproceedings)

am ics

PDF DOI [BibTex]

PDF DOI [BibTex]


no image
Deep Learning for Tactile Understanding From Visual and Haptic Data

Gao, Y., Hendricks, L. A., Kuchenbecker, K. J., Darrell, T.

In Proceedings of the IEEE International Conference on Robotics and Automation, pages: 536-543, May 2016, Oral presentation given by Gao (inproceedings)

hi

[BibTex]

[BibTex]


no image
Robust Tactile Perception of Artificial Tumors Using Pairwise Comparisons of Sensor Array Readings

Hui, J. C. T., Block, A. E., Taylor, C. J., Kuchenbecker, K. J.

In Proceedings of the IEEE Haptics Symposium, pages: 305-312, Philadelphia, Pennsylvania, USA, April 2016, Oral presentation given by Hui (inproceedings)

hi

[BibTex]

[BibTex]


no image
Data-Driven Comparison of Four Cutaneous Displays for Pinching Palpation in Robotic Surgery

Brown, J. D., Ibrahim, M., Chase, E. D. Z., Pacchierotti, C., Kuchenbecker, K. J.

In Proceedings of the IEEE Haptics Symposium, pages: 147-154, Philadelphia, Pennsylvania, USA, April 2016, Oral presentation given by Brown (inproceedings)

hi

[BibTex]

[BibTex]


Multisensory Robotic Therapy through Motion Capture and Imitation for Children with ASD
Multisensory Robotic Therapy through Motion Capture and Imitation for Children with ASD

Burns, R., Nizambad, S., Park, C. H., Jeon, M., Howard, A.

Proceedings of the American Society of Engineering Education, Mid-Atlantic Section, Spring Conference, April 2016 (conference)

Abstract
It is known that children with autism have difficulty with emotional communication. As the population of children with autism increases, it is crucial we create effective therapeutic programs that will improve their communication skills. We present an interactive robotic system that delivers emotional and social behaviors for multi­sensory therapy for children with autism spectrum disorders. Our framework includes emotion­-based robotic gestures and facial expressions, as well as tracking and understanding the child’s responses through Kinect motion capture.

hi

link (url) [BibTex]

link (url) [BibTex]


no image
Design and Implementation of a Visuo-Haptic Data Acquisition System for Robotic Learning of Surface Properties

Burka, A., Hu, S., Helgeson, S., Krishnan, S., Gao, Y., Hendricks, L. A., Darrell, T., Kuchenbecker, K. J.

In Proceedings of the IEEE Haptics Symposium, pages: 350-352, April 2016, Work-in-progress paper. Poster presentation given by Burka (inproceedings)

hi

Project Page [BibTex]

Project Page [BibTex]


no image
Supplemental material for ’Communication Rate Analysis for Event-based State Estimation’

Ebner, S., Trimpe, S.

Max Planck Institute for Intelligent Systems, January 2016 (techreport)

am ics

PDF [BibTex]

PDF [BibTex]


no image
Psychophysical Power Optimization of Friction Modulation for Tactile Interfaces

Sednaoui, T., Vezzoli, E., Gueorguiev, D., Amberg, M., Chappaz, C., Lemaire-Semail, B.

In Haptics: Perception, Devices, Control, and Applications, pages: 354-362, Springer International Publishing, Cham, 2016 (inproceedings)

Abstract
Ultrasonic vibration and electrovibration can modulate the friction between a surface and a sliding finger. The power consumption of these devices is critical to their integration in modern mobile devices such as smartphones. This paper presents a simple control solution to reduce up to 68.8 {\%} this power consumption by taking advantage of the human perception limits.

hi

[BibTex]

[BibTex]


Effect of Waveform in Haptic Perception of Electrovibration on Touchscreens
Effect of Waveform in Haptic Perception of Electrovibration on Touchscreens

Vardar, Y., Güçlü, B., Basdogan, C.

In Haptics: Perception, Devices, Control, and Applications, pages: 190-203, Springer International Publishing, Cham, 2016 (inproceedings)

Abstract
The perceived intensity of electrovibration can be altered by modulating the amplitude, frequency, and waveform of the input voltage signal applied to the conductive layer of a touchscreen. Even though the effect of the first two has been already investigated for sinusoidal signals, we are not aware of any detailed study investigating the effect of the waveform on our haptic perception in the domain of electrovibration. This paper investigates how input voltage waveform affects our haptic perception of electrovibration on touchscreens. We conducted absolute detection experiments using square wave and sinusoidal input signals at seven fundamental frequencies (15, 30, 60, 120, 240, 480 and 1920 Hz). Experimental results depicted the well-known U-shaped tactile sensitivity across frequencies. However, the sensory thresholds were lower for the square wave than the sinusoidal wave at fundamental frequencies less than 60 Hz while they were similar at higher frequencies. Using an equivalent circuit model of a finger-touchscreen system, we show that the sensation difference between the waveforms at low fundamental frequencies can be explained by frequency-dependent electrical properties of human skin and the differential sensitivity of mechanoreceptor channels to individual frequency components in the electrostatic force. As a matter of fact, when the electrostatic force waveforms are analyzed in the frequency domain based on human vibrotactile sensitivity data from the literature [15], the electrovibration stimuli caused by square-wave input signals at all the tested frequencies in this study are found to be detected by the Pacinian psychophysical channel.

hi

vardar_eurohaptics_2016 [BibTex]

vardar_eurohaptics_2016 [BibTex]


no image
Compliant control for soft robots: emergent behavior of a tendon driven anthropomorphic arm.

Martius, G., Hostettler, R., Knoll, A., Der, R.

In 2016 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS), pages: 767-773, 2016 (inproceedings)

al

DOI [BibTex]

DOI [BibTex]

2015


no image
Distributed Event-based State Estimation

Trimpe, S.

Max Planck Institute for Intelligent Systems, November 2015 (techreport)

Abstract
An event-based state estimation approach for reducing communication in a networked control system is proposed. Multiple distributed sensor-actuator-agents observe a dynamic process and sporadically exchange their measurements and inputs over a bus network. Based on these data, each agent estimates the full state of the dynamic system, which may exhibit arbitrary inter-agent couplings. Local event-based protocols ensure that data is transmitted only when necessary to meet a desired estimation accuracy. This event-based scheme is shown to mimic a centralized Luenberger observer design up to guaranteed bounds, and stability is proven in the sense of bounded estimation errors for bounded disturbances. The stability result extends to the distributed control system that results when the local state estimates are used for distributed feedback control. Simulation results highlight the benefit of the event-based approach over classical periodic ones in reducing communication requirements.

am ics

arXiv [BibTex]

2015


arXiv [BibTex]


Automatic LQR Tuning Based on Gaussian Process Optimization: Early Experimental Results
Automatic LQR Tuning Based on Gaussian Process Optimization: Early Experimental Results

Marco, A., Hennig, P., Bohg, J., Schaal, S., Trimpe, S.

Machine Learning in Planning and Control of Robot Motion Workshop at the IEEE/RSJ International Conference on Intelligent Robots and Systems (iROS), pages: , , Machine Learning in Planning and Control of Robot Motion Workshop, October 2015 (conference)

Abstract
This paper proposes an automatic controller tuning framework based on linear optimal control combined with Bayesian optimization. With this framework, an initial set of controller gains is automatically improved according to a pre-defined performance objective evaluated from experimental data. The underlying Bayesian optimization algorithm is Entropy Search, which represents the latent objective as a Gaussian process and constructs an explicit belief over the location of the objective minimum. This is used to maximize the information gain from each experimental evaluation. Thus, this framework shall yield improved controllers with fewer evaluations compared to alternative approaches. A seven-degree-of-freedom robot arm balancing an inverted pole is used as the experimental demonstrator. Preliminary results of a low-dimensional tuning problem highlight the method’s potential for automatic controller tuning on robotic platforms.

am ei ics pn

PDF DOI Project Page [BibTex]

PDF DOI Project Page [BibTex]


no image
Assessing human-human therapy kinematics for retargeting to human-robot therapy

Johnson, M. J., Christopher, S. M., Mohan, M., Mendonca, R.

In Proceedings of the IEEE International Conference on Rehabilitation Robotics (ICORR), Singapore, August 2015 (inproceedings)

Abstract
In this paper, we present experiments examining the accuracy of data collected from a Kinect sensor for capturing close interactive actions of a therapist with a patient during stroke rehabilitation. Our long-term goal is to map human-human interactions such as these patient-therapist ones onto human-robot interactions. In many robot interaction scenarios, the robot does not mimic interaction between two or more humans, which is a major part of stroke therapy. The Kinect works for functional tasks such as a reaching task where the interaction to be retargeted by the robot is minimal to none; though this data is not good for a functional task involving touching another person. We demonstrate that the noisy data from Kinect does not produce a system robust enough to be for remapping to a humanoid robot a therapit's movements when in contact with a person.

hi

DOI [BibTex]

DOI [BibTex]


Direct Loss Minimization Inverse Optimal Control
Direct Loss Minimization Inverse Optimal Control

Doerr, A., Ratliff, N., Bohg, J., Toussaint, M., Schaal, S.

In Proceedings of Robotics: Science and Systems, Rome, Italy, Robotics: Science and Systems XI, July 2015 (inproceedings)

Abstract
Inverse Optimal Control (IOC) has strongly impacted the systems engineering process, enabling automated planner tuning through straightforward and intuitive demonstration. The most successful and established applications, though, have been in lower dimensional problems such as navigation planning where exact optimal planning or control is feasible. In higher dimensional systems, such as humanoid robots, research has made substantial progress toward generalizing the ideas to model free or locally optimal settings, but these systems are complicated to the point where demonstration itself can be difficult. Typically, real-world applications are restricted to at best noisy or even partial or incomplete demonstrations that prove cumbersome in existing frameworks. This work derives a very flexible method of IOC based on a form of Structured Prediction known as Direct Loss Minimization. The resulting algorithm is essentially Policy Search on a reward function that rewards similarity to demonstrated behavior (using Covariance Matrix Adaptation (CMA) in our experiments). Our framework blurs the distinction between IOC, other forms of Imitation Learning, and Reinforcement Learning, enabling us to derive simple, versatile, and practical algorithms that blend imitation and reinforcement signals into a unified framework. Our experiments analyze various aspects of its performance and demonstrate its efficacy on conveying preferences for motion shaping and combined reach and grasp quality optimization.

am ics

PDF Video Project Page [BibTex]

PDF Video Project Page [BibTex]


no image
LMI-Based Synthesis for Distributed Event-Based State Estimation

Muehlebach, M., Trimpe, S.

In Proceedings of the American Control Conference, July 2015 (inproceedings)

Abstract
This paper presents an LMI-based synthesis procedure for distributed event-based state estimation. Multiple agents observe and control a dynamic process by sporadically exchanging data over a broadcast network according to an event-based protocol. In previous work [1], the synthesis of event-based state estimators is based on a centralized design. In that case three different types of communication are required: event-based communication of measurements, periodic reset of all estimates to their joint average, and communication of inputs. The proposed synthesis problem eliminates the communication of inputs as well as the periodic resets (under favorable circumstances) by accounting explicitly for the distributed structure of the control system.

am ics

PDF DOI Project Page [BibTex]

PDF DOI Project Page [BibTex]


no image
Guaranteed H2 Performance in Distributed Event-Based State Estimation

Muehlebach, M., Trimpe, S.

In Proceeding of the First International Conference on Event-based Control, Communication, and Signal Processing, June 2015 (inproceedings)

am ics

PDF DOI Project Page [BibTex]

PDF DOI Project Page [BibTex]


no image
On the Choice of the Event Trigger in Event-based Estimation

Trimpe, S., Campi, M.

In Proceeding of the First International Conference on Event-based Control, Communication, and Signal Processing, June 2015 (inproceedings)

am ics

PDF DOI Project Page [BibTex]

PDF DOI Project Page [BibTex]


no image
Toward a large-scale visuo-haptic dataset for robotic learning

Burka, A., Hu, S., Krishnan, S., Kuchenbecker, K. J., Hendricks, L. A., Gao, Y., Darrell, T.

In Proc. CVPR Workshop on the Future of Datasets in Vision, 2015 (inproceedings)

hi

Project Page [BibTex]

Project Page [BibTex]


no image
Detecting Lumps in Simulated Tissue via Palpation with a BioTac

Hui, J., Block, A., Kuchenbecker, K. J.

In Proc. IEEE World Haptics Conference, 2015, Work-in-progress paper. Poster presentation given by Hui (inproceedings)

hi

[BibTex]

[BibTex]


no image
Analysis of the Instrument Vibrations and Contact Forces Caused by an Expert Robotic Surgeon Doing FRS Tasks

Brown, J. D., O’Brien, C., Miyasaka, K., Dumon, K. R., Kuchenbecker, K. J.

In Proc. Hamlyn Symposium on Medical Robotics, pages: 75-76, London, England, June 2015, Poster presentation given by Brown (inproceedings)

hi

[BibTex]

[BibTex]


no image
Should Haptic Texture Vibrations Respond to User Force and Speed?

Culbertson, H., Kuchenbecker, K. J.

In IEEE World Haptics Conference, pages: 106 - 112, Evanston, Illinois, USA, June 2015, Oral presentation given by Culbertson (inproceedings)

hi

[BibTex]

[BibTex]


no image
Enabling the Baxter Robot to Play Hand-Clapping Games

Fitter, N. T., Neuburger, M., Kuchenbecker, K. J.

In Proc. IEEE World Haptics Conference, June 2015, Work-in-progress paper. Poster presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Event-based Estimation and Control for Remote Robot Operation with Reduced Communication

Trimpe, S., Buchli, J.

In Proceedings of the IEEE International Conference on Robotics and Automation, May 2015 (inproceedings)

Abstract
An event-based communication framework for remote operation of a robot via a bandwidth-limited network is proposed. The robot sends state and environment estimation data to the operator, and the operator transmits updated control commands or policies to the robot. Event-based communication protocols are designed to ensure that data is transmitted only when required: the robot sends new estimation data only if this yields a significant information gain at the operator, and the operator transmits an updated control policy only if this comes with a significant improvement in control performance. The developed framework is modular and can be used with any standard estimation and control algorithms. Simulation results of a robotic arm highlight its potential for an efficient use of limited communication resources, for example, in disaster response scenarios such as the DARPA Robotics Challenge.

am ics

PDF DOI Project Page [BibTex]

PDF DOI Project Page [BibTex]


no image
Using IMU Data to Teach a Robot Hand-Clapping Games

Fitter, N. T., Kuchenbecker, K. J.

In Proc. IEEE Haptics Symposium, pages: 353-355, April 2015, Work-in-progress paper. Poster presentation given by Fitter (inproceedings)

hi

[BibTex]

[BibTex]


no image
Haptic Feedback in Transoral Robotic Surgery: A Feasibility Study

Bur, A. M., Gomez, E. D., Rassekh, C. H., Newman, J. G., Weinstein, G. S., Kuchenbecker, K. J.

In Proc. Annual Meeting of the Triological Society at COSM, April 2015, Poster presentation given by Bur (inproceedings)

hi

[BibTex]

[BibTex]


no image
Human Machine Interface for Dexto Eka: - The humanoid robot

Kumra, S., Mohan, M., Gupta, S., Vaswani, H.

In Proceedings of the IEEE International Conference on Robotics, Automation, Control and Embedded Systems (RACE), Chennai, India, Febuary 2015 (inproceedings)

Abstract
This paper illustrates hybrid control system of the humanoid robot, Dexto:Eka: focusing on the dependent or slave mode. Efficiency of any system depends on the fluid operation of its control system. Here, we elucidate the control of 12 DoF robotic arms and an omnidirectional mecanum wheel drive using an exo-frame, and a Graphical User Interface (GUI) and a control column. This paper comprises of algorithms, control mechanisms and overall flow of execution for the regulation of robotic arms, graphical user interface and locomotion.

hi

DOI [BibTex]

DOI [BibTex]


no image
Conception and development of Dexto:Eka: The Humanoid Robot - Part IV

Kumra, S., Mohan, M., Vaswani, H., Gupta, S.

In Proceedings of the IEEE International Conference on Robotics, Automation, Control and Embedded Systems (RACE), Febuary 2015 (inproceedings)

Abstract
This paper elucidates the fourth phase of the development of `Dexto:Eka: - The Humanoid Robot'. It lays special emphasis on the conception of the locomotion drive and the development of vision based system that aids navigation and tele-operation. The first three phases terminated with the completion of two robotic arms with six degrees of freedom each, structural development and the creation of a human machine interface that included an exo-frame, a control column and a graphical user interface. This phase also involved the enhancement of the exo-frame to a vision based system using a Kinect camera. The paper also focuses on the reasons behind choosing the locomotion drive and the benefits it has.

hi

DOI [BibTex]

DOI [BibTex]


no image
Design and Validation of a Practical Simulator for Transoral Robotic Surgery

Bur, A. M., Gomez, E. D., Chalian, A. A., Newman, J. G., Weinstein, G. S., Kuchenbecker, K. J.

In Proc. Society for Robotic Surgery Annual Meeting: Transoral Program, (T8), February 2015, Oral presentation given by Bur (inproceedings)

hi

[BibTex]

[BibTex]


no image
A New Perspective and Extension of the Gaussian Filter

Wüthrich, M., Trimpe, S., Kappler, D., Schaal, S.

In Robotics: Science and Systems, 2015 (inproceedings)

Abstract
The Gaussian Filter (GF) is one of the most widely used filtering algorithms; instances are the Extended Kalman Filter, the Unscented Kalman Filter and the Divided Difference Filter. GFs represent the belief of the current state by a Gaussian with the mean being an affine function of the measurement. We show that this representation can be too restrictive to accurately capture the dependencies in systems with nonlinear observation models, and we investigate how the GF can be generalized to alleviate this problem. To this end we view the GF from a variational-inference perspective, and analyze how restrictions on the form of the belief can be relaxed while maintaining simplicity and efficiency. This analysis provides a basis for generalizations of the GF. We propose one such generalization which coincides with a GF using a virtual measurement, obtained by applying a nonlinear function to the actual measurement. Numerical experiments show that the proposed Feature Gaussian Filter (FGF) can have a substantial performance advantage over the standard GF for systems with nonlinear observation models.

am ics

Web PDF Project Page [BibTex]

2010


no image
VerroTouch: High-Frequency Acceleration Feedback for Telerobotic Surgery

Kuchenbecker, K. J., Gewirtz, J., McMahan, W., Standish, D., Martin, P., Bohren, J., Mendoza, P. J., Lee, D. I.

In Haptics: Generating and Perceiving Tangible Sensations, Proc. EuroHaptics, Part I, 6191, pages: 189-196, Lecture Notes in Computer Science, Springer, Amsterdam, Netherlands, July 2010, Oral presentation given by Kuchenbecker (inproceedings)

hi

[BibTex]

2010


[BibTex]


no image
Automatic Filter Design for Synthesis of Haptic Textures from Recorded Acceleration Data

Romano, J. M., Yoshioka, T., Kuchenbecker, K. J.

In Proc. IEEE International Conference on Robotics and Automation, pages: 1815-1821, Anchorage, Alaska, USA, May 2010, Oral presentation given by Romano (inproceedings)

hi

[BibTex]

[BibTex]


no image
Control of a High Fidelity Ungrounded Torque Feedback Device: The iTorqU 2.1

Winfree, K. N., Romano, J. M., Gewirtz, J., Kuchenbecker, K. J.

In Proc. IEEE International Conference on Robotics and Automation, pages: 1347-1352, Anchorage, Alaska, May 2010, Oral presentation given by Winfree (inproceedings)

hi

[BibTex]

[BibTex]


no image
High Frequency Acceleration Feedback Significantly Increases the Realism of Haptically Rendered Textured Surfaces

McMahan, W., Romano, J. M., Rahuman, A. M. A., Kuchenbecker, K. J.

In Proc. IEEE Haptics Symposium, pages: 141-148, Waltham, Massachusetts, March 2010, Oral presentation given by McMahan (inproceedings)

hi

[BibTex]

[BibTex]


no image
Spatially distributed tactile feedback for kinesthetic motion guidance

Kapur, P., Jensen, M., Buxbaum, L. J., Jax, S. A., Kuchenbecker, K. J.

In Proc. IEEE Haptics Symposium, pages: 519-526, Waltham, Massachusetts, USA, March 2010, Poster presentation given by Kapur. {F}inalist for Best Poster Award (inproceedings)

hi

[BibTex]

[BibTex]


no image
Accelerometer-based Tilt Estimation of a Rigid Body with only Rotational Degrees of Freedom

Trimpe, S., D’Andrea, R.

In Proceedings of the IEEE International Conference on Robotics and Automation, 2010 (inproceedings)

am ics

PDF DOI [BibTex]

PDF DOI [BibTex]