Header logo is


2020


Changes in Normal Force During Passive Dynamic Touch: Contact Mechanics and Perception
Changes in Normal Force During Passive Dynamic Touch: Contact Mechanics and Perception

Gueorguiev, D., Lambert, J., Thonnard, J., Kuchenbecker, K. J.

In Proceedings of the IEEE Haptics Symposium (HAPTICS), pages: 746-752, Washington, USA, March 2020 (inproceedings)

Abstract
Using a force-controlled robotic platform, we investigated the contact mechanics and psychophysical responses induced by negative and positive modulations in normal force during passive dynamic touch. In the natural state of the finger, the applied normal force modulation induces a correlated change in the tangential force. In a second condition, we applied talcum powder to the fingerpad, which induced a significant modification in the slope of the correlated tangential change. In both conditions, the same ten participants had to detect the interval that contained a decrease or an increase in the pre-stimulation normal force of 1 N. In the natural state, the 75% just noticeable difference for this task was found to be a ratio of 0.19 and 0.18 for decreases and increases, respectively. With talcum powder on the fingerpad, the normal force thresholds remained stable, following the Weber law of constant just noticeable differences, while the tangential force thresholds changed in the same way as the correlation slopes. This result suggests that participants predominantly relied on the normal force changes to perform the detection task. In addition, participants were asked to report whether the force decreased or increased. Their performance was generally poor at this second task even for above-threshold changes. However, their accuracy slightly improved with the talcum powder, which might be due to the reduced finger-surface friction.

hi

DOI [BibTex]

2020


DOI [BibTex]

2015


no image
Human Machine Interface for Dexto Eka: - The humanoid robot

Kumra, S., Mohan, M., Gupta, S., Vaswani, H.

In Proceedings of the IEEE International Conference on Robotics, Automation, Control and Embedded Systems (RACE), Chennai, India, Febuary 2015 (inproceedings)

Abstract
This paper illustrates hybrid control system of the humanoid robot, Dexto:Eka: focusing on the dependent or slave mode. Efficiency of any system depends on the fluid operation of its control system. Here, we elucidate the control of 12 DoF robotic arms and an omnidirectional mecanum wheel drive using an exo-frame, and a Graphical User Interface (GUI) and a control column. This paper comprises of algorithms, control mechanisms and overall flow of execution for the regulation of robotic arms, graphical user interface and locomotion.

hi

DOI [BibTex]

2015


DOI [BibTex]


no image
Conception and development of Dexto:Eka: The Humanoid Robot - Part IV

Kumra, S., Mohan, M., Vaswani, H., Gupta, S.

In Proceedings of the IEEE International Conference on Robotics, Automation, Control and Embedded Systems (RACE), Febuary 2015 (inproceedings)

Abstract
This paper elucidates the fourth phase of the development of `Dexto:Eka: - The Humanoid Robot'. It lays special emphasis on the conception of the locomotion drive and the development of vision based system that aids navigation and tele-operation. The first three phases terminated with the completion of two robotic arms with six degrees of freedom each, structural development and the creation of a human machine interface that included an exo-frame, a control column and a graphical user interface. This phase also involved the enhancement of the exo-frame to a vision based system using a Kinect camera. The paper also focuses on the reasons behind choosing the locomotion drive and the benefits it has.

hi

DOI [BibTex]

DOI [BibTex]

2013


no image
Governance of Humanoid Robot Using Master Exoskeleton

Kumra, S., Mohan, M., Gupta, S., Vaswani, H.

In Proceedings of the IEEE International Symposium on Robotics (ISR), Seoul, South Korea, October 2013 (inproceedings)

Abstract
Dexto:Eka: is an adult-size humanoid robot being developed with the aim of achieving tele-presence. The paper sheds light on the control of this robot using a Master Exoskeleton which comprises of an Exo-Frame, a Control Column and a Graphical User Interface. It further illuminates the processes and algorithms that have been utilized to make an efficient system that would effectively emulate a tele-operator.

hi

DOI [BibTex]

2013


DOI [BibTex]


no image
Design and development part 2 of Dexto:Eka: - The humanoid robot

Kumra, S., Mohan, M., Gupta, S., Vaswani, H.

In Proceedings of the International Conference on Mechatronics and Automation (ICMA), Takamatsu, Japan, August 2013 (inproceedings)

Abstract
Through this paper, we elucidate the second phase of the design and development of the tele-operated humanoid robot Dexto:Eka:. Phase one comprised of the development of a 6 DoF left anthropomorphic arm and left exo-frame. Here, we illustrate the development of the right arm, right exo-frame, torso, backbone, human machine interface and omni-directional locomotion system. Dexto:Eka: will be able to communicate with a remote user through Wi-Fi. An exo-frame capacitates it to emulate human arms and its locomotion is controlled by joystick. A Graphical User Interface monitors and helps in controlling the system.

hi

DOI [BibTex]

DOI [BibTex]